爱普生EPSON喷墨打印机报故障错误代码033001解决方法

错误代码
Code:
031004

 Head temperature error
打印头温度错误

• Disconnection, break, skew or damage of the head FFC
• Occurs after receiving a print job and starting

printing
Failure of the thermistor inside the printhead Temperature around the printhead is out of the range from -20 to 80 degrees C.
•打印头FFC断开、断裂、倾斜或损坏
•在收到打印作业并启动后发生

打印头内部热敏电阻失效打印头周围的温度超出了-20到80摄氏度的范围。

1. Check the head FFC for disconnection, break, skew or damage.
2. Replace the printhead with a new one.
3. Replace the main board with a new one.
1。检查打印头FFC是否断开、断裂、歪斜或损坏。
2。用新的打印头更换。
3。所示。更换新的主板。

Main board CN42
主板CN42

错误代码
Code:
031006

Blowout of a fuse error (Head)
保险丝烧断错误(打印头)

• Failure of the power source for the printhead
1. Failure of the circuit
Disconnection, break, skew, or damage of the head FFC
2. Blowout of fuse on the main board Failure of the printhead
• Occurs at power-on, when replacing the ink cartridge, in-between print passes, and after flushing operation
•打印头电源故障
1。电路故障
打印头FFC断开、断裂、歪斜或损坏
2。主板上保险丝烧断打印头故障
•在接通电源、更换墨盒时、在打印通道之间以及冲洗操作后发生

1. If the fuse has not blown out
• Check the head FFC for disconnection, break, skew or damage.
2. If the fuse has blown out
• Replace the main board with a new one.
3. In the other cases
• Replace the printhead with a new one.
1。如果保险丝没有烧断
•检查打印头FFC是否断开、断裂、歪斜或损坏。
2。如果保险丝烧断了
•更换主板。
3所示。在其他情况下
•更换新的打印头。

Main board CN43
主板CN43

故障代码
Code:
031008

 VBS

overvoltage error
VBS电压错误

1. Head FFC failure (skew, foreign object attached)
2. Failure of the head
3. Failure of the main board
(Occurrence frequency based on past record is 1. > 2. > 3.)
1.打印头FFC故障(歪斜，有异物附着)
2.打印机头故障
3.打印机主板故障
(基于过往记录的发生频率为1。> 2。> 3)。

1. Check the head FFC.
2. Replace the printhead with a new one.
3. Replace the main board with a new one.
1。检查打印头FFC。
2。用新的打印头更换。
3。更换机器主板。

Main board CN41
主板CN41

故障代码
Code:
033001

Blowout of a fuse error (CRCM)
熔断错误(CRCM)

• Failure of the main board
• Occurs at power-on, and during operation for replacing the ink cartridge
•主板故障
•开机时发生，以及在更换墨盒时发生

1. Check the CRCM FFC for disconnection, break, skew or damage.
2. If the error still occurs after the restart, replace the main board.
1。检查CRCM FFC是否断开、断裂、歪斜或损坏。
2。如果重启后仍然出现错误，请更换主板。

Main board CN43
主板CN43